QC Inspector II or QC Inspector III at Shalby Advanced Technologies Inc

El Dorado Hills, California, United States -

Full Time

Start Date

Immediate

Expiry Date

29 May, 26

Salary

24.5

Posted On

28 Feb, 26

Experience

2 year(s) or above

Remote Job

Yes

Telecommute

Yes

Sponsor Visa

Skills

Inspection, Quality Control, First Article Inspection, In-Process Inspection, Final Inspection, Material Review Board, Statistical Sampling, ANSI/ASQ Z1.4, GD&T, Calipers, Micrometers, Go/No-Go Gauges, Optical Comparators, CMM Operating, Calypso Software, Surface Plate Setups

Industry

Medical Device

Description

Description The work schedule for this position is: Monday through Thursday, 6am-4:30pm The Quality Control Inspector II/III is responsible for routine (incoming, in-process, first article and final) QC inspection of raw materials, subassemblies and finished product. All receiving, in-process, first article and final inspections are performed in accordance with documented procedures and specifications. The QC Inspector II/III shall use inspection equipment that is properly calibrated, handled and maintained. The QC Inspector II/III documents inspection results and releases acceptable product for use. The QC Inspector II/III identifies and segregates nonconforming product/processes for disposition by the Material Review Board. The Quality Control Inspector II/III is responsible for performance of the following quality system functions in accordance with documented procedures: Inspection– Performing first article, receiving, in-process and final inspections in accordance with documented procedures. Assisting other personnel with inspection setups and questions. Process Control – Maintain product identification and traceability requirements throughout the inspection processes. Nonconformance Handling – Identification, documentation, evaluation, and segregation of nonconforming product pending review and disposition by the Material Review Board. Statistical Techniques – Employment of the appropriate statistical sampling techniques for inspection by attributes (ANSI/ASQ Z1.4). Requirements This position requires the following qualifications (at a minimum): QC Inspector II At least 2 years of experience performing inspections in a regulated industry such as medical device, automotive, aerospace. Adequate knowledge and understanding of the applicable quality system requirements (ISO 13485:2016, 21 CFR Part 820, etc.); Adequate knowledge and understanding of industry-standards for the sampling (ANSI/ASQ Z1.4) and inspection of product; Excellent organizational and communication skills. The ability to follow directions and interpret engineering and inspection specifications, including GD&T. Experience with a variety of inspection instruments such as calipers, micrometers, go/no-go gauges and Optical Comparators. CMM operating experience with Calypso software. CMM programming being a plus. Experience with developing open inspection setups on surface plates using height gages, sine plates etc. Experience with the inspection of high polished, tumbled, sand blasted and satin brushed surface finishes is a plus. Good written and verbal communication skills and familiar with problem solving skills. Familiar with computer applications, such as, Word, Excel, email and ERP Systems. Ability to make complex decisions and change tasks in a timely manner. May require long periods of sitting or standing and occasional lifting up to 40 lbs. Requires a high school diploma or its equivalent. QC Inspector III At least 4 years of experience performing inspections in a regulated industry such as medical device, automotive, aerospace. Adequate knowledge and understanding of the applicable quality system requirements (ISO 13485:2016, 21 CFR Part 820, etc.); Adequate knowledge and understanding of industry-standards for the sampling (ANSI/ASQ Z1.4) and inspection of product; Excellent organizational and communication skills. The ability to follow directions and interpret engineering and inspection specifications, including GD&T. Experience with a variety of inspection instruments such as calipers, micrometers, go/no-go gauges and Optical Comparators. CMM programming experience with Calypso software. Experience with developing open inspection setups on surface plates using height gages, sine plates etc. Experience with the inspection of high polished, tumbled, sand blasted and satin brushed surface finishes is a plus. Good written and verbal communication skills and familiar with problem solving skills. Familiar with computer applications, such as Word, Excel, email and ERP Systems. Ability to make complex decisions and change tasks in a timely manner. May require long periods of sitting or standing and occasional lifting up to 40 lbs. Requires a high school diploma or its equivalent. The expected base salary range for this position is between $22.50 to $24.50 per hour and the compensation offered will depend on the candidate’s qualifications. We offer company holidays, vacation and sick time off, medical, dental, vision, disability and life benefits as well as a 401(k) Plan. Shalby Advanced Technologies, Inc. provides equal employment opportunities to applicants and employees without regard to: age, genetic information/characteristics, marital status, medical condition, mental or physical disability, national origin and ancestry, pregnancy and perceived pregnancy, race and color, religion, sex/gender including pregnancy, breastfeeding, gender identity or gender expression, sexual stereotypes, sexual orientation, reproductive health decision-making and veteran or military status.

Responsibilities

The Quality Control Inspector II/III performs routine inspections of raw materials, subassemblies, and finished products according to documented procedures, utilizing calibrated equipment and documenting results. This role also involves identifying and segregating nonconforming product for disposition by the Material Review Board and maintaining product traceability.